search

Auto-zone-control-systems SS0070 USB-Link Technical Guide, Installation Inst Manual de usuario Pagina 4

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 20
  • Tabla de contenidos
  • SOLUCIÓN DE PROBLEMAS
    •
  • MARCADORES
    • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 3
USB-Link Technical Guide
4
Operator Interface
Important Notes
Follow the included USB-Link driver installation
instructions. Make sure you follow the appropriate
directions for your Windows
®
version - Windows
®
XP
directions are different from Windows
®
Vista.
Follow the connection and wiring instructions
(Figure 2 on page 5) to connect and confi gure the
USB-Link.
If you use your USB-Link on a network and after
installation you cannot view all controllers, you may
need an EPROM upgrade in your CommLink(s) and/
or MiniLink(s). See Troubleshooting in the back of
this guide on page 16 for further instructions.
Familiarize yourself with all system components and
review all documentation. Pay special attention to
“Cautions,” “Notes,” and “Warnings” since these may
keep you from experiencing unnecessary problems.
If you encounter any problems, please refer to the
Troubleshooting section of this guide fi rst. If you
can’t resolve the problem, please call WattMaster
Technical Support at our toll free number—
1-866-918-1100.
Quick Guide for Windows XP
Follow the fi ve steps below to get your USB-Link up and running in
no time.
Step 1: Set your USB-Link’s communication switch to
Stand Alone or Network. See Figure 3 on page 12.
Step 2: Attach the USB cable to your USB-Link and plug
the other end of the cable into your computer’s
USB port. See Figure 2 on page 5.
Step 3: Attach the communication cable to your USB-Link
and connect the other end of the cable to the
Controller’s communication port. See Figure 2 on
page 5.
Step 4: Install the USB drivers located on the included
CD-ROM.
Step 5: Install the included Prism II software on your
computer.
Quick Guide
Quick Guide for Windows Vista & 7
Follow the fi ve steps below to get your USB-Link up and running in
no time.
Step 1: Set your USB-Link’s communication switch to Stand Alone
or Network. See Figure 3 on page 12.
Step 2: Install the USB drivers from the included CD-ROM onto
your computer.
Step 3: Attach the USB cable to your USB-Link and plug
the other end of the cable into your computer’s
USB port. See Figure 2 on page 5.
Step 4: Attach the communication cable to your USB-Link
and connect the other end of the cable to the
Controller’s communication port. See Figure 2 on
page 5.
Step 5: Install the included Prism II software on your
computer.
Revised 1/24/11
Vista de pagina 3
1 2 3 4 5 6 7 8 9 ... 19 20

Comentarios a estos manuales

Sin comentarios
Relacionado con productos y manuales para Equipo Auto-zone-control-systems SS0070 USB-Link Technical Guide, Installation Inst
Equipo Auto-zone-control-systems Auto-Zone Basic Systems Installation & Operati Manual de usuario   (150 paginas)
  • Michaelo Espresso Lava-mobiles UBIQUIT Advantage Engineering PRG
  • Shure Equipo de música complementario Epson Impresión y escaneo ION Accesorios reproductores de mp3 / mp4 Brecknell Balanzas De Correos Holmes No
  • Gemini PMX-120 Aeg-Electrolux T75470AH Sony BDP-S6200 Russell Hobbs Jewels Zanussi ZGH62414WA
  • Acer EB275U Manual de usuario Bowers & Wilkins DM601 Manual de usuario Dell S1709W Manual de usuario Vizualogic A-2000 El manual del propietario Samsung GT-S6800 Manual de usuario